Tuesday 25 October 2011

FLAT OTG CABLE ...by C/D


[ITALIAN]
Quanti cavetti OTG avete usato senza che funzionassero correttamente?
Quante guide avete seguito e non hanno portato ai risultati voluti?
Quanti cavetti avete acquistato ed erano troppo ingombranti per le vostre esigenze?
Se come me avete uno Xoom (con Honeycomb 3.1), o un altro device con USB HOST, e desiderare un cavetto OTG piatto col minimo ingombro, allora questa guida fa per voi.

Innanzitutto l'occorrente:
- 1 MicroUSB Type-B maschio
- 1 USB Type-A femmina
- 1 piatra mille-fori
- 6 cavetti dei colori rosso, nero, bianco, verde, blue e viola
- 1 foglio di plastica adesiva nero lucido

La lista dei componenti è esigua, ma alcuni componenti sono difficili da reperire nei negozi di elettronica.
Per questo motivo sarebbe utile ricorrere al disassemblaggio di vecchi cavetti, oppure ancor meglio ordinarli online.
Prendere la piastra-mille fori, stampare e ritagliare la fig. 2 come indicato, riportare le misure dello schema sulla piastra.
Aprire sulla piastra mille-fori la fessura per la porta usb Micro-B, quindi saldare tutte le porte usb femmina e maschio.
Prendere i cavetti e saldarli sulla piastra mille-fori come riportato nelle fig. 1-3.
Ora dovreste aver ottenuto quanto riportato in fig. 3; testare il circuito, provare innanzitutto che non vi siano corti tra le saldature, poi effettuare l'ultima prova collegando il cavetto al vostro Xoom.
Se i collegamenti sono corretti, tra i capi dei cavetti rosso e nero deve essere presente una differenza di potenziale di 5V, se così non è allora ricontrollate i collegamenti e riprovare.
A questo punto sagomare la piastra come da disegno.
Fissare la porta Micro-B con della colla a caldo, una volta raffreddata la colla proseguire a ricoprire tutta la superficie del bottom fino ad ottenere uno strato di alcuni millimetri.
Ricordate di raffreddare sempre la superficie prima di proseguire a mettere e togliere la colla a caldo per modellarla.
Terminato ciò, incollare la plastica adesiva nero lucido. Tagliare e sagomare la plastica; il risultato sarà quello riportato nella foto di presentazione.
Di seguito sono riportate le figure e le foto dei vari passaggi.
Se la guida vi è piaciuta provateci e buon divertimento!


[ENGLISH]
How OTG cables you used to work properly without?
How many guides have followed and didn't lead to the desired results?
How many cables you have purchased and were too bulky for your needs?
If like me you have a Xoom (with Honeycomb 3.1), or another device with USB Host, and you want a flat OTG cable with a small footprint, then this guide is for you.

First you need:
- 1 MicroUSB Type-B Male
- 1 USB Type-A Female
- 1 plate thousand-holes
- 6 cables of color red, black, white, green, blue and purple
- 1 sheet of adhesive plastic glossy black

The list of components is small, but some parts are hard to find in electronics stores.
For this reason it would be helpful to use the disassembly of old cables, or better still order them online.
Take the plate-thousand holes, print and cut out the fig. 2 as indicated, return of the key measures on the plate.
Open on thousand-holes the plate for the slot of Micro-B USB port, then solder the USB ports female and male.
Take the wires and solder them on the plate thousand-holes as shown in fig. 1-3.
Now you should have gotten as shown in fig. 3, test the circuit, first try that there are no shorts between the welds, then make the ultimate test by connecting the cable to your Xoom.
If the connections are correct, between the heads of red and black wires must be a potential difference of 5V, if it isn't, then recheck your connections and try again.
At this point cut the plate as shape drawn.
Attach the door of Micro-B with hot glue, the glue when cooled further to cover the entire surface of the bottom layer until you get a few millimeters.
Always remember to cool the surface before heading into and out of hot glue to shape it.
After this, glue the shiny black plastic adhesive. Cut and shape the plastic and the result will be shown in the photo presentation.
Here are the pictures and photos of various steps.
If you liked the guide will try it and have fun!
























The schematics_table.pdf, all in one pdf.

P.S.
An answer for everyone who had doubts about the compatibility with 2.0 devices.
In the video I used a usb hub connected to flat otg cable....

No comments:

Post a Comment

Hi at all, leave me a feedback for this post. Thx